160 lines
7.2 KiB
Plaintext
160 lines
7.2 KiB
Plaintext
# Example PlatformIO Project Configuration Override
|
|
# ------------------------------------------------------------------------------
|
|
# Copy to platformio_override.ini to activate overrides
|
|
# ------------------------------------------------------------------------------
|
|
# Please visit documentation: https://docs.platformio.org/page/projectconf.html
|
|
|
|
[platformio]
|
|
default_envs = WLED_tasmota_1M
|
|
|
|
[env:WLED_tasmota_1M]
|
|
board = esp01_1m
|
|
platform = ${common.platform_wled_default}
|
|
platform_packages = ${common.platform_packages}
|
|
board_build.ldscript = ${common.ldscript_1m128k}
|
|
lib_deps = ${esp8266.lib_deps}
|
|
build_unflags = ${common.build_unflags}
|
|
build_flags = ${common.build_flags_esp8266}
|
|
; *********************************************************************
|
|
; *** Use custom settings from file my_config.h
|
|
-DWLED_USE_MY_CONFIG
|
|
; *********************************************************************
|
|
;
|
|
;
|
|
; *** To use the below defines/overrides, copy and paste each onto it's own line just below build_flags in the section above.
|
|
;
|
|
; disable specific features
|
|
; -D WLED_DISABLE_OTA
|
|
; -D WLED_DISABLE_ALEXA
|
|
; -D WLED_DISABLE_HUESYNC
|
|
; -D WLED_DISABLE_INFRARED
|
|
; -D WLED_DISABLE_WEBSOCKETS
|
|
; PIN defines - uncomment and change, if needed:
|
|
; -D LEDPIN=2
|
|
; -D BTNPIN=0
|
|
; -D TOUCHPIN=T0
|
|
; -D IRPIN=4
|
|
; -D RLYPIN=12
|
|
; -D RLYMDE=1
|
|
; digital LED strip types - uncomment only one ! - this will disable WS281x / SK681x support
|
|
; -D USE_APA102
|
|
; -D USE_WS2801
|
|
; -D USE_LPD8806
|
|
; PIN defines for 2 wire LEDs
|
|
-D CLKPIN=0
|
|
-D DATAPIN=2
|
|
; to drive analog LED strips (aka 5050) hardware configuration is no longer necessary
|
|
; configure the settings in the UI as follows (hard):
|
|
; for the Magic Home LED Controller use PWM pins 5,12,13,15
|
|
; for the H801 controller use PINs 15,13,12,14 (W2 = 04)
|
|
; for the BW-LT11 controller use PINs 12,4,14,5
|
|
;
|
|
; set the name of the module - make sure there is a quote-backslash-quote before the name and a backslash-quote-quote after the name
|
|
; -D SERVERNAME="\"WLED\""
|
|
;
|
|
; set the number of LEDs
|
|
; -D DEFAULT_LED_COUNT=30
|
|
;
|
|
; set milliampere limit when using ESP pin to power leds
|
|
; -D ABL_MILLIAMPS_DEFAULT=850
|
|
;
|
|
; enable IR by setting remote type
|
|
; -D IRTYPE=0 ;0 Remote disabled | 1 24-key RGB | 2 24-key with CT | 3 40-key blue | 4 40-key RGB | 5 21-key RGB | 6 6-key black | 7 9-key red | 8 JSON remote
|
|
;
|
|
; set default color order of your led strip
|
|
; -D DEFAULT_LED_COLOR_ORDER=COL_ORDER_GRB
|
|
|
|
|
|
# ------------------------------------------------------------------------------
|
|
# Hub75 examples from upstream WLED
|
|
# ! Just for reference -> will need some adjust to work with WLED-MM !
|
|
# ------------------------------------------------------------------------------
|
|
|
|
;[env:esp32dev_hub75]
|
|
;board = esp32dev
|
|
;upload_speed = 921600
|
|
;platform = ${esp32_idf_V4.platform}
|
|
;platform_packages = ${esp32_idf_V4.platform_packages}
|
|
;build_unflags = ${common.build_unflags}
|
|
;build_flags = ${common.build_flags}
|
|
; -D WLED_RELEASE_NAME=\"ESP32_hub75\"
|
|
; -D WLED_ENABLE_HUB75MATRIX -D NO_GFX
|
|
; -D WLED_DEBUG_BUS
|
|
; ; -D WLED_DEBUG
|
|
; -D SR_DMTYPE=1 -D I2S_SDPIN=-1 -D I2S_CKPIN=-1 -D I2S_WSPIN=-1 -D MCLK_PIN=-1 ;; Disable to prevent pin clash
|
|
;lib_deps = ${esp32_idf_V4.lib_deps}
|
|
; https://github.com/mrfaptastic/ESP32-HUB75-MatrixPanel-DMA.git#3.0.11
|
|
;monitor_filters = esp32_exception_decoder
|
|
;board_build.partitions = ${esp32.default_partitions}
|
|
;board_build.flash_mode = dio
|
|
;custom_usermods = audioreactive
|
|
|
|
;[env:esp32dev_hub75_forum_pinout]
|
|
;extends = env:esp32dev_hub75
|
|
;build_flags = ${common.build_flags}
|
|
; -D WLED_RELEASE_NAME=\"ESP32_hub75_forum_pinout\"
|
|
; -D WLED_ENABLE_HUB75MATRIX -D NO_GFX
|
|
; -D ESP32_FORUM_PINOUT ;; enable for SmartMatrix default pins
|
|
; -D WLED_DEBUG_BUS
|
|
; -D SR_DMTYPE=1 -D I2S_SDPIN=-1 -D I2S_CKPIN=-1 -D I2S_WSPIN=-1 -D MCLK_PIN=-1 ;; Disable to prevent pin clash
|
|
|
|
|
|
;[env:adafruit_matrixportal_esp32s3]
|
|
;; ESP32-S3 processor, 8 MB flash, 2 MB of PSRAM, dedicated driver pins for HUB75
|
|
;board = adafruit_matrixportal_esp32s3_wled
|
|
;;; adafruit recommends to use arduino-esp32 2.0.14
|
|
;;;platform = espressif32@ ~6.5.0
|
|
;;;platform_packages = platformio/framework-arduinoespressif32 @ 3.20014.231204 ;; arduino-esp32 2.0.14
|
|
;platform = ${esp32s3.platform}
|
|
;platform_packages = ${esp32s3.platform_packages}
|
|
;upload_speed = 921600
|
|
;build_unflags = ${common.build_unflags}
|
|
;build_flags = ${common.build_flags} ${esp32s3.build_flags} -D WLED_RELEASE_NAME=\"ESP32-S3_8M_qspi\"
|
|
; -DARDUINO_USB_CDC_ON_BOOT=1 ;; -DARDUINO_USB_MODE=1 ;; for boards with USB-OTG connector only (USBCDC or "TinyUSB")
|
|
; -DBOARD_HAS_PSRAM
|
|
; -DLOLIN_WIFI_FIX ; seems to work much better with this
|
|
; -D WLED_WATCHDOG_TIMEOUT=0
|
|
; -D WLED_ENABLE_HUB75MATRIX -D NO_GFX
|
|
; -D S3_LCD_DIV_NUM=20 ;; Attempt to fix wifi performance issue when panel active with S3 chips
|
|
; -D ARDUINO_ADAFRUIT_MATRIXPORTAL_ESP32S3
|
|
; -D WLED_DEBUG_BUS
|
|
; -D SR_DMTYPE=1 -D I2S_SDPIN=-1 -D I2S_CKPIN=-1 -D I2S_WSPIN=-1 -D MCLK_PIN=-1 ;; Disable to prevent pin clash
|
|
;lib_deps = ${esp32s3.lib_deps}
|
|
; https://github.com/mrfaptastic/ESP32-HUB75-MatrixPanel-DMA.git#aa28e2a ;; S3_LCD_DIV_NUM fix
|
|
;
|
|
;board_build.partitions = ${esp32.large_partitions} ;; standard bootloader and 8MB Flash partitions
|
|
;; board_build.partitions = tools/partitions-8MB_spiffs-tinyuf2.csv ;; supports adafruit UF2 bootloader
|
|
;board_build.f_flash = 80000000L
|
|
;board_build.flash_mode = qio
|
|
;monitor_filters = esp32_exception_decoder
|
|
;;custom_usermods = audioreactive
|
|
|
|
;[env:esp32S3_PSRAM_HUB75]
|
|
;;; MOONHUB HUB75 adapter board (lilygo T7-S3 with 16MB flash and PSRAM)
|
|
;board = lilygo-t7-s3
|
|
;platform = ${esp32s3.platform}
|
|
;platform_packages = ${esp32s3.platform_packages}
|
|
;upload_speed = 921600
|
|
;build_unflags = ${common.build_unflags}
|
|
; ${Speed_Flags.build_unflags} ;; optional: removes "-Os" so we can override with "-O2" in build_flags
|
|
;build_flags = ${common.build_flags} ${esp32s3.build_flags} -D WLED_RELEASE_NAME=\"esp32S3_16MB_PSRAM_HUB75\"
|
|
; ${Speed_Flags.build_flags} ;; optional: -O2 -> optimize for speed instead of size
|
|
; -DARDUINO_USB_CDC_ON_BOOT=1 ;; -DARDUINO_USB_MODE=1 ;; for boards with USB-OTG connector only (USBCDC or "TinyUSB")
|
|
; -DBOARD_HAS_PSRAM
|
|
; -DLOLIN_WIFI_FIX ; seems to work much better with this
|
|
; -D WLED_WATCHDOG_TIMEOUT=0
|
|
; -D WLED_ENABLE_HUB75MATRIX -D NO_GFX
|
|
; -D S3_LCD_DIV_NUM=20 ;; Attempt to fix wifi performance issue when panel active with S3 chips
|
|
; -D MOONHUB_S3_PINOUT ;; HUB75 pinout
|
|
; -D WLED_DEBUG_BUS
|
|
; -D LEDPIN=14 -D BTNPIN=0 -D RLYPIN=15 -D IRPIN=-1 -D AUDIOPIN=-1 ;; defaults that avoid pin conflicts with HUB75
|
|
; -D SR_DMTYPE=1 -D I2S_SDPIN=10 -D I2S_CKPIN=11 -D I2S_WSPIN=12 -D MCLK_PIN=-1 ;; I2S mic
|
|
;lib_deps = ${esp32s3.lib_deps}
|
|
; https://github.com/mrfaptastic/ESP32-HUB75-MatrixPanel-DMA.git#aa28e2a ;; S3_LCD_DIV_NUM fix
|
|
;;;board_build.partitions = ${esp32.large_partitions} ;; for 8MB flash
|
|
;board_build.partitions = ${esp32.extreme_partitions} ;; for 16MB flash
|
|
;board_build.f_flash = 80000000L
|
|
;board_build.flash_mode = qio
|
|
;monitor_filters = esp32_exception_decoder
|
|
;;custom_usermods = audioreactive
|