"sound pressure" for line-in was always close to max - which is expected, because the ADC chip utilize the full 24/16bit sample range.
The new calculation leads to some more "movement".
* 40Hz low-cut and DC blocker filter - will remove any signal offsets and also removes rumbling noise up to 12db
* DC blocker set as default for all sources (prerequisite for later measuring sound pressure)
additional filtering options are in the making :-)
This mode freezes MicLev even fast. However it makes some assumptions that may not always be true:
* At least 12 seconds of silence during start
* a high quality microphone with very low noise level.
--> If you are not sure about these preconditions, better use normal "Freeze" mode.
- micLev: "freeze" mode - should help to prevent short "dropout" wen music is playing
- freqRMS: if set to "On", will use a different method for averaging higher frequencies. May give you more action in GEQ. Could lead to GEQ "overshooting" as Mic Profiles are not adjusted to this method.
* const.h: static json buffer (usermod settings pages) was getting tight, added some margin
pio.ini: enable WLED_DEBUG_HOST in esp32_4MB_M_debug and esp32_16MB_M_debug
audio_reactive, um6050, wled.h
- replace DEBUGOUT.print(x) by DEBUGOUT(x) etc
wled.h: switch between serial/netdebug
cfg.cpp, set.cpp, wled.cpp, xml.cpp
- store netDebugPrintIP and netDebugPrintPort in cfg.json
index.js: rename info tab on off to Net Debug
settings.sync: add netdebug
net_debug.h/cpp: use global netDebugPrintIP remove debugPrintHostIP
Audio reactive usermod: add pio.ini build flags defaults (⎌) for mclk, sda and scl (if set)
4ld usermod:
- if pio.ini build flags not set, make them -1 (undefined is even better but then problems with allocate pins, to be done later)
- pio.ini build flags defaults (⎌) different if spi (clockspi and mosispi instead of scl and sda)
- add pio.ini build flags defaults (⎌) for SPI CS, DC and RESET
- shorten oappend MM function names
- add aOpt: analog options only
- add pin 17 for esp8266 (analog pin)
- add a.pins array to show analog pins in pin dropdown
some optimizations for -C3.
* skip every second FFT, and use interpolation instead.
* reduce sampling rate from 22Khz to 18Khz
* new debug measurement for I2S cycle times (FFTTask)
--> in total, this brings CPU load for sound processing down to 60% (from >100% previously)
AudioReactive: add disableROPins on WS, SCK, MCLK and SCL
4LD: add disableROPins on CLK
settingsum:
- addfield: max 49 pins, if (global interface) also disabled, rename if to global, show 🔴 if pin claimed
- add disableROPins
- pinDropdownsPost
- rename SDA to if:SDA (etc) so it is part of claimed pins (also in set.cpp and xml.cpp)
xml.cpp:
- appendGPIOinfo(): get rsvd and ro_gpio from pinManager.isPinOk instead of hardcoded
- getSettingsJS: add pinDropdownsPost
- replace rOption by xOption (extend option) to show default value (⎌)
- Usermod rotary_encoder: add appendConfigData function and show help and default functions
- Settings.htm: Move Usermods(pins) below the usermods
Settings_um.htm
- remove SDAPin etc
- comment check(0,k) as not used anymore
- add xOption
- add generated global pin fields (using addField) in ldS
- remove hard coded global pin fields
set.cpp: set i2c_sda etc using new generated fields
xml.cpp: set generated fields values using i2c_sda etc and show defaults
- rename replaceOption to rOption
- rename removeOptions to dOptions
- set oAppend buffer size back to 3096
- WLEDMM warning on settings2D Populate
- add AppendConfig per usermod
- add request parameter to getSettinsJS
- add lookupName
make the serial plotter graphs easier to read:
* physical samples scaled down to 50%
* added 256 for all effect vars, so their graph will always be above the physical samples lines
got myself an adafruit "qt py -S2" with tinyUF2 bootloader. So I wanted to get that working. And it does work :-).
FFT time = 10ms (instead of 2ms on classic ESP32) is a very good result, also virtual USB runs much better now.
- new partition table for boards with UF2 boot (Adafruit qt py S2)
- better treatment of debug out using "USBCDC" native port
- workarounds for watchdog crashes on -S2
- Add missing but mandatory build flags for -S2 and -C3
