... like the typical -C3
* Replaced a few direct Serial.printf with macros
* Always check if Serial is connected before printing (CDC sometimes hangs when trying to send/receive without connection)
pio.ini: enable WLED_DEBUG_HOST in esp32_4MB_M_debug and esp32_16MB_M_debug
audio_reactive, um6050, wled.h
- replace DEBUGOUT.print(x) by DEBUGOUT(x) etc
wled.h: switch between serial/netdebug
cfg.cpp, set.cpp, wled.cpp, xml.cpp
- store netDebugPrintIP and netDebugPrintPort in cfg.json
index.js: rename info tab on off to Net Debug
settings.sync: add netdebug
net_debug.h/cpp: use global netDebugPrintIP remove debugPrintHostIP
Some additions:
pio.ini: add debug entries
cfg.cpp, set.cpp, xml/cpp: keep storing basic 2D setup
index.js: use ledmapFileNames
settings_2D.htm: keep using basic and advanced
FX_2Dfcn.cpp: use gaptable and also MM ledmaps
FX_fcn.cpp: extend enumerateledmaps with AC ledmapNames (but not used in UI)
* Support white addressable LED strips
* Various white handling tweaks
Allow RGB controls for white-only busses depending on AWM (makes palette-only FX work on non-RGB addressable busses)
Fixed RGB controls hidden if segment contained any non-RGB bus (even though there is also an RGB bus in that segment)
New Max auto white mode
Added hasCCT() bus method
Rename methods to be clearer
WS2811 White getPixelColor fix()
* Fix merge conflict (bus manager cpp)
as it turns out, also on 8266 any pin can be assigned to I2C. Only SPI pins are fixed, and GPIO16 should not be used as it does not support interrupts.
platformio
- create _all entries (wip)
- set FLD_PIN_SCL to -1 (use global)
4ld
- one bug fix and errorMessage improvements
const.h
- comments
wled.h
- do not use the I2CSDAPIN vars but HW_PIN_SDA instead
Usermod bh1750: only save pins if not equal to global
Usermod fld: add errorMessage, do not reset type and enabled but errormessage instead, show global depending in spi or i2c
cfg.cpp and set.cpp: do not reset global i2c or spi if error
Improve co-existence of several popular usermods with respect to shared I2C bus.
- ensure that i2c_sda and i2c_scl are used when defined
- ensure that HW_PIN_SDA / HW_PIN_SCL are not overwritten
- ensure that Wire.begin()nis always called with user-defined pins (remove rogue Wire.begin() without parameters)
- ensure that set.cpp / cfg.cpp use esp32-specific global Wire objects.
- switch off debug messages to USBCDC, if WLED_DEBUG is not set
- ensure that analogread pins are valid - invalid pins cause lots of error messages and finally lead to watchdog reset on some MCUs.
* add 9 further alexa devices for calling presets 1-9
* use preset names from WLED for Alexa preset device names instead of hardcoded names
* update readme and version
* call alexaInit() at end of savePreset() to keep Alexa in sync with the preset IDs and names
* This reverts commit f8db06c7c5cfe159f9fc03ebc08547fa3c9e9ebd.
* change order to configured Alexa WLED name first, preset names afterwards
* fix status of devices when shown within Alexa, i.e. switching one preset on switches others off (except for alexaInvocationName)
* re-add getPresetName() after merge with master
* restore original readme for pull request
* restore original platformio.ini for pull request
* Logic simplification
* Pass string by reference
* Added number of presets check
* fix alexaInit() in case of alexaNumPresets==0
Co-authored-by: Christian Schwinne <dev.aircoookie@gmail.com>
