FX.h: add ledsrgbSize and allocLeds()
FX_fcn.cpp:
- copy constructor: allocLeds()
- move constructor: no change
- copy assignment: reuse! + allocLeds()
- move asignment: no change
- resetIfRequired: no free
- setUpLeds/resetSegments: allocLeds()
unless...: copy constructor aften called. That is the bad boy causing re-allocs at every effect change!
*This patch allows to compile with BOARD_HAS_PSRAM, but not set WLED_USE_PSRAM - reserved pins will be protected, and PSRAM usage will be shown in info.
* if you add `-D WLED_USE_PSRAM_JSON` then PSRAM will be used for some JSON buffers, but not for LEDs and Segments.
* xml.cpp: correct type for checkbox global led buffer" (was not shown correctly)
* fx.cpp: 2D floating blobs - correct swapped x/y coordinates (did not render correctly on non-square matrix)
pio.ini: enable WLED_DEBUG_HOST in esp32_4MB_M_debug and esp32_16MB_M_debug
audio_reactive, um6050, wled.h
- replace DEBUGOUT.print(x) by DEBUGOUT(x) etc
wled.h: switch between serial/netdebug
cfg.cpp, set.cpp, wled.cpp, xml.cpp
- store netDebugPrintIP and netDebugPrintPort in cfg.json
index.js: rename info tab on off to Net Debug
settings.sync: add netdebug
net_debug.h/cpp: use global netDebugPrintIP remove debugPrintHostIP
Some additions:
pio.ini: add debug entries
cfg.cpp, set.cpp, xml/cpp: keep storing basic 2D setup
index.js: use ledmapFileNames
settings_2D.htm: keep using basic and advanced
FX_2Dfcn.cpp: use gaptable and also MM ledmaps
FX_fcn.cpp: extend enumerateledmaps with AC ledmapNames (but not used in UI)
* Support white addressable LED strips
* Various white handling tweaks
Allow RGB controls for white-only busses depending on AWM (makes palette-only FX work on non-RGB addressable busses)
Fixed RGB controls hidden if segment contained any non-RGB bus (even though there is also an RGB bus in that segment)
New Max auto white mode
Added hasCCT() bus method
Rename methods to be clearer
WS2811 White getPixelColor fix()
* Fix merge conflict (bus manager cpp)
Audio reactive usermod: add pio.ini build flags defaults (⎌) for mclk, sda and scl (if set)
4ld usermod:
- if pio.ini build flags not set, make them -1 (undefined is even better but then problems with allocate pins, to be done later)
- pio.ini build flags defaults (⎌) different if spi (clockspi and mosispi instead of scl and sda)
- add pio.ini build flags defaults (⎌) for SPI CS, DC and RESET
- shorten oappend MM function names
- add aOpt: analog options only
- add pin 17 for esp8266 (analog pin)
- add a.pins array to show analog pins in pin dropdown
bugfix: replace oappend(SET_F(name)); by oappend(_name);
const.h: remove unset of 8266 variables as no behind the scene actions, this is just bad behavior and the pin drop downs will show this bad behavior
xml.cpp: show hardware defaults as ⍼ in dropdowns (better icon needed)
AudioReactive: add disableROPins on WS, SCK, MCLK and SCL
4LD: add disableROPins on CLK
settingsum:
- addfield: max 49 pins, if (global interface) also disabled, rename if to global, show 🔴 if pin claimed
- add disableROPins
- pinDropdownsPost
- rename SDA to if:SDA (etc) so it is part of claimed pins (also in set.cpp and xml.cpp)
xml.cpp:
- appendGPIOinfo(): get rsvd and ro_gpio from pinManager.isPinOk instead of hardcoded
- getSettingsJS: add pinDropdownsPost
